Worx WG896 Electric Lawn Edger Review for Homeowners
As an Amazon Associate we earn from qualifying purchases.
The Worx WG896 lawn edger is a corded electric tool with a 7.5 inch blade, a 12 Amp motor and three cutting depth settings. It is built for homeowners who want a sharp, straight border along a walkway, driveway or flower bed without a gas engine. The listing describes it as a dual-use tool for edging and light trenching, so it can cut a clean line in the lawn edge and also cut a shallow trench for wire or cable. This review covers what the listing states, how the tool is set up, and which accessories the listing data lists for it.
Quick answer
- The WG896 is a corded electric edger with a 12 Amp motor and a 7.5 inch blade.
- It offers three cutting depths: 1 inch, 1-1/4 inch and 1-1/2 inch.
- The listing gives a 4700 RPM blade speed, an adjustable shaft and a cutting line indicator.
- It has a built-in 1 foot power cord and needs an extension cord to operate, and the listing states a 3 year limited manufacturer warranty.
Who the WG896 suits
This edger fits a homeowner with a small to medium yard that has clear edges to maintain. The depth settings help with two jobs. At 1 inch, the tool trims the grass line neatly along a path. At the deeper settings, it cuts a trench that can hold a cable or a sprinkler line. The listing names both uses under the dual-use item highlight, so those are the jobs it is designed for.
It is less suited to people who want a cordless tool. The WG896 needs an outlet and an extension cord, so plan the route before you start. If your edging area is far from an outlet, a cordless edger or a longer cord will be needed. The listing data includes a cordless edger and trimmer guide on this site, which covers those options in more detail.
Specifications from the listing
The table below uses the values that appear in the listing data. Where the listing does not state a value, the table says so.
| Feature | What the listing states |
|---|---|
| Power source | Corded electric |
| Motor | 12 Amp |
| Blade size | 7.5 inches (cutting width listed as 7.5 inches) |
| Blade speed | 4700 revolutions per minute |
| Cutting depth settings | Three: 1 inch, 1-1/4 inch and 1-1/2 inch |
| Shaft | Adjustable shaft with a D-grip handle |
| Cord | Built-in 1 foot power cord; extension cord required |
| Item weight | 14 pounds |
| Item dimensions | 22.6 inches long by 14.1 inches wide |
| Included components | One 12 Amp lawn edger and trencher, one 7.5 inch blade |
| Warranty | 3 years limited, as stated by the manufacturer |
| Model | WG896 |
Cutting performance
The listing says the 12 Amp motor spins the 7.5 inch blade at 4700 revolutions per minute. That speed is the main figure for cutting action. A faster blade cuts a cleaner edge through grass and soil, and the listing ties that speed to the sharp, professional-looking lines it describes. The blade is a serrated design in the replacement listings in this guide, which suggests the same shape on the stock blade, but the WG896 listing itself does not describe the blade profile in detail, so check the blade on the tool when it arrives.
The depth settings control how far the blade cuts into the soil. At the 1 inch setting, the cut is shallow, which suits a clean edge along lawn borders. The 1-1/4 inch and 1-1/2 inch settings cut deeper, and the 1-1/2 inch setting is the one most suited to trenching. The listing does not state how many passes a trench at each depth needs, so the time to dig a given length will vary with soil and root density.
Shaft, grip and cutting line
The adjustable shaft lets users of different heights set a comfortable working position. The listing describes a D-grip handle at the top of the shaft. Set the shaft height before you start, so you do not bend your back through a full run of edging.
The cutting line indicator is a guide on the tool that helps you keep the blade on a straight line. The listing says it helps keep the edge straight, and it is useful when you are following a walkway or driveway. Move slowly along the line, and let the blade cut at its own pace rather than pushing it hard into the soil.
Setup and cord use
The WG896 has a built-in power cord of 1 foot, so you will always need an extension cord to reach an outlet. The listing does not name an extension cord, and the listing data lists one bundled with a WG896 kit. That bundle includes a 50 foot outdoor extension cord with a lighted end, and the listing describes it as suitable for outdoor use, resistant to moisture, abrasion and sunlight, and ETL listed. Check the cord gauge and length against your run before you connect it, and keep the cord clear of the blade path.
Assembly is simple from what the listing states. The tool ships with one 7.5 inch blade installed. Keep the tool unplugged while you change depth settings or check the blade. The listing does not describe a tool-free blade change, so use the bolt and nut method described in the replacement blade listings.
Replacement blades and kits
Several listings state that replacement blades fit the WG896. The WORX WA0034 blade listing describes a 7.5 inch replacement blade with serrated edges and wear indicators, and it notes three blades per package. Other third-party blade listings name the WG896 as a compatible model, and they give part numbers such as WA0034 and 50018386. Before buying a third-party blade, confirm the part number on your original blade, since the listings say to make sure the number matches.
A kit listing in the listing data combines the WG896 with replacement blades. It describes the same 12 Amp edger with three replacement blades in one package, which can save a second purchase if you expect to swap blades over several seasons.
Mistakes to avoid
- Running the cord across the blade path, which can cause a trip or a snag on the cord.
- Choosing the 1-1/2 inch depth for a light edging job, which cuts deeper than the job needs.
- Assuming the 14 pound weight is light for a long session. Plan breaks on a large edging run.
- Buying a blade that does not match the part number on the original blade.
Safety basics from the listing
The listing identifies the WG896 as a corded tool, so the first safety step is to keep the power cord away from the blade and to unplug the tool before you change the blade or adjust the depth. Wear eye protection and gloves when you handle a spinning blade, and keep bystanders and pets clear. The listing does not state a specific safety standard beyond the ETL mark on the bundled cord, so follow the owner’s manual that ships with the tool.
FAQ
Is the Worx WG896 a corded or cordless edger?
It is corded. The listing states a built-in 1 foot power cord, and it requires an extension cord to operate.
What cutting depths does the WG896 offer?
The listing states three depth settings: 1 inch, 1-1/4 inch and 1-1/2 inch.
How big is the blade?
The blade is 7.5 inches, and the listing gives a 4700 revolutions per minute speed for the 12 Amp motor.
What warranty does the WG896 carry?
The listing states a 3 year limited manufacturer warranty.
Can I use it to trench for wire?
The listing describes the tool as a dual-use edger and trencher, with a 1-1/2 inch depth setting. Use the deepest setting for trenching, and check local rules before you dig.
Does the WG896 come with replacement blades?
The base tool includes one 7.5 inch blade. Replacement blades are sold separately, and the listing data lists kits that include three blades.
Bottom line
Choose the WG896 if you want a corded edger for crisp lawn borders and shallow trenching, and you have an outlet near the work area. Check the cord run before you buy, and plan for a replacement blade in the future. If you need to cut a long edge without an outlet, look at a cordless option instead.
For more on edging technique, read How to Edge a Lawn With an Electric Edger. If you are comparing cordless options, see Best Cordless Lawn Edgers and String Trimmers Compared.
Related listings with the WG896
The listings below include the same WG896 edger in a different package. Their stated contents differ from the base tool, so read each listing before you buy.
WORX WG896 edger with replacement blades kit
This kit pairs the 12 Amp, 7.5 inch WG896 edger with replacement blades. The listing states three replacement blades in the package, along with the same depth settings, 4700 RPM speed and cutting line indicator as the base tool.
WORX WG896 edger with 50 foot extension cord
This package pairs the WG896 edger with a 50 foot outdoor extension cord that has a lighted end. The listing states that the cord resists moisture, abrasion and sunlight and carries an ETL listing. Use the cord for the edger’s run, and confirm the cord’s gauge against the tool’s power draw before you connect it.
Sources
All product facts come from the listing data for this review.
