Best Dust Extractor

As an Amazon Associate we earn from qualifying purchases.

The person typing best dust extractor wants a machine that pulls fine dust from a sander, saw, router or hammer drill where the work happens, and that runs on a power source they already own. The nine listings we opened on 2026-10-22 fall into three groups: tool-only units that need a separate battery, corded wet-dry extractors that state airflow and cord length, and one mobile kit for hammer drilling that includes a battery. Only that kit states a battery in the box. Every figure below comes from a listing, and the gaps are listed too.

Quick answer

If you already own DEWALT 20V MAX or FLEXVOLT batteries, start with the DEWALT DWH161B or DCV585B. Both are built around that platform, and neither listing states a battery in the box.
If you have no battery platform, a corded unit is the simpler choice. The Makita VC4210L lists a 12 amp motor, 148 CFM of suction and an 11-gallon tank, and the two Fein Turbo I sets list 151 CFM with a 19 ft cord.
For SDS-plus hammer drilling with a battery included, the Bosch GDE18V-26DB15 kit lists one CORE18V 4 Ah battery and a dust container for up to 20 holes.
Check the airflow figures before you compare. The DEWALT DWV010 listing gives two numbers, 150 CFM and 155 CFM, and the listing does not say which one applies.

The nine listings side by side

The table holds only the columns the listings state. A cell that reads not stated means the extracted listing text is silent on that point. Airflow is shown as each listing gives it, and the Makita XCV04Z gives two figures because its corded and battery numbers differ.

Listing (ASIN)	Power source	Battery in the box	Capacity	Airflow as stated	Filter	Cord or hose
DEWALT DWH161B (B07WQB34DX)	20V MAX battery, tool only	Not stated	Not stated	Not stated	HEPA included	Not stated
DEWALT DWV010 (B00OA02TZ0)	Corded, 120 V	Not applicable	8 gallon	150 CFM (bullet); 155 CFM (description)	HEPA, automatic clean	15 ft hose
DEWALT DCV585B (B07N2KBM8W)	FLEXVOLT 20V/60V MAX battery	Not stated	Not stated	125 CFM	Dual HEPA filters, automatic clean	8 ft hose
Makita XCV11Z (B07M8JTDNS)	18V LXT battery, tool only	Not included	2 gallon	57 CFM, 27 in water lift	Cartridge HEPA	Not stated
Makita VC4210L (B07ZMN75V2)	Corded	Not applicable	11 gallon	148 CFM, 92 in water lift	HEPA, two-stage	Not stated
Makita XCV04Z (B01FXQ6CLQ)	Corded, or two 18V LXT batteries	Not included	2.1 gallon	127 CFM corded; 74 CFM on batteries	Three-stage HEPA	Not stated
Fein Turbo I Set (B00K69ILFQ)	Corded	Not applicable	5.8 gallon	151 CFM, 98 water lift	HEPA filter included	19 ft cord, 13 ft hose
Fein Turbo I HEPA Pro Set (B0CKDT5WPM)	Corded	Not applicable	5.8 gallon	151 CFM, 98 water lift	HEPA filter and filter bag	19 ft cord, 13 ft hose
Bosch GDE18V-26DB15 (B07PS7NDRT)	18V CORE18V battery	One 4 Ah battery	Up to 20 holes	Not stated	HEPA	Not stated

The nine products, one by one

Each section gives what the listing says, one case where that product is the wrong choice, and one limit the listing leaves open. The sections are in no particular order and are not a ranking.

DEWALT DWH161B 20V MAX Dust Extractor (tool only)

This is a tool-only extractor for the 20V MAX platform. The listing names SDS Plus rotary hammers as its main use and also lists sanders, routers and jig saws. It says the unit is optimized for SDS Plus rotary hammers while drilling and chipping, and that it is part of an OSHA 1926.1153 Table 1 compliant solution when paired with the correct shroud and a rotary hammer.

Power: 20V MAX battery platform, tool only (title)
Battery and charger: not stated as included; the title says tool only
Filter: HEPA filter included in the dust box (listing)
Capacity: 45% more than the DWH302DH dust box (listing)
Wireless tool control: links the extractor and a tool; key fob sold separately (listing)
Airflow, weight and hose length: not stated

Skip it if you need a standalone extractor for floor-level cleanup, since the listing ties the unit to rotary hammers and power tools. Its limit is that the listing gives no airflow figure. View on Amazon

DEWALT DWV010 8-Gallon HEPA Dust Extractor (corded)

The DWV010 is a corded 8-gallon HEPA extractor with automatic filter cleaning. The listing says the filter pulses every 30 seconds so the unit keeps running without stopping to clean the filter. It has heavy-duty wheels, a universal hose connector with swivel, and an outlet that a power tool can switch on and off.

Power: corded; voltage 120 (listing)
Motor: 15 amp (listing)
Airflow: 150 CFM in a bullet and 155 CFM in the description; the listing gives both
Filter: HEPA with automatic clean every 30 seconds (listing)
Hose: 15 ft anti-static, 1.25 in diameter (listing)
Weight: 21 lbs (description)
Battery: not applicable

Skip it if the job is far from an outlet. The listing also says it meets the EPA Lead Related Renovations, Repair and Painting Rule only when DWV9330 filters are used, so plan for those filters if that rule applies to your work. Its limit is the two airflow figures on one page.

DEWALT DCV585B FLEXVOLT 60V MAX Dust Extractor

The DCV585B is a cordless extractor that the listing says runs off the FLEXVOLT 20V/60V MAX battery. The listing describes dual filters that clean automatically, HEPA filters, a remote for wireless tool control, and T-Stak stacking with other DEWALT storage. Its airflow is stated as 125 CFM for OSHA Table 1 work with an appropriate dust shroud, such as up to 5-inch tuckpointing and surfacing.

Power: FLEXVOLT 20V/60V MAX battery (description)
Airflow: 125 CFM (listing)
Filters: dual filters with automatic filter cleaning; HEPA included (listing)
Hose: 8 ft anti-static with AIRLOCK, with a built-in hose wrap (listing)
Wireless tool control: with the included remote, or a wireless-enabled tool (listing)
Battery and charger in the box: not stated
Weight: not stated

Skip it if you do not own a FLEXVOLT battery, because the listing ties the unit to that battery. Its limit is that the listing does not say whether a battery comes with it. For another FLEXVOLT tool, see our FLEXVOLT 60V max string trimmer guide.

Makita XCV11Z 18V LXT 2-Gallon Wet/Dry Extractor (tool only)

The XCV11Z is a cordless 2-gallon wet/dry extractor for the 18V LXT platform. The listing says its brushless motor delivers 57 CFM and 27 inches of water lift when it runs on an 18V LXT battery, and that the unit weighs 10.1 pounds with a 5.0Ah battery. The listing states that the battery is not included.

Power: 18V LXT battery, tool only; battery not included (listing)
Capacity: 2 gallon (title)
Airflow: 57 CFM and 27 inches water lift (listing)
Filter: cartridge; HEPA captures 99.97% of particulates, 3 microns and larger (listing)
Runtime: up to 60 minutes on an 18V LXT 5.0Ah battery, which is not included (listing)
Weight: 10.1 pounds with the 5.0Ah battery (listing)
Hose length: not stated

Skip it if you have no 18V LXT battery, because the listing gives its runtime and weight only with one. The limit is that the runtime figure assumes the 5.0Ah battery the listing names. For the voltage and amp-hour numbers behind battery platforms like this one, see our lawn mower battery voltage and amp hours guide.

Makita VC4210L 11-Gallon Wet/Dry HEPA Extractor (corded)

The VC4210L is a corded 11-gallon wet/dry extractor. The listing says a 12 amp motor makes 148 CFM of suction and 92 inches of water lift, and it describes the unit for dust extraction in concrete and woodworking. Its on-board tool-activated outlet starts and stops the vacuum with the tool, with a 10-second delay to clear remaining debris.

Power: corded (listing)
Capacity: 11 gallon (title)
Motor: 12 amp (listing)
Airflow: 148 CFM and 92 inches of water lift (listing)
Filter: HEPA, 99.97% of particulates 3 microns and larger; two-stage filtration with a main flat filter that captures 99.95% of particles 2 microns and larger (listing)
Automatic filter cleaning: yes (listing)
Weight and hose length: not stated

Skip it if you need a cordless unit or the job is far from an outlet. The limit is that the listing gives no weight or hose length, so you cannot judge how easily the unit moves between rooms from the listing alone.

Makita XCV04Z 2.1-Gallon Corded or 36V Extractor (tool only)

The XCV04Z runs on corded power or on two 18V LXT batteries, which the listing describes as 36V. Corded, the listing gives 127 CFM and 96 inches of water lift. On two batteries, it gives 74 CFM and 36 inches. The batteries are not included.

Power: corded, or two 18V LXT batteries (listing)
Capacity: 2.1 gallon (title)
Airflow: 127 CFM and 96 inches water lift corded; 74 CFM and 36 inches on batteries (listing)
Runtime: up to 65 minutes on low and 30 minutes on high, with two 18V 5.0Ah batteries (listing; batteries not included)
Filter: three-stage HEPA (listing)
Battery and charger: not included (listing)
Weight and hose length: not stated

Skip it if you have only one battery, since the listing says cordless operation needs two. Its limit is that the battery airflow is lower than the corded figure and the listing gives no reason. The listing’s own phrase, “offers corded or cordless operation for maximum versatility and convenience,” is a claim about the design, not a measured result.

Fein Turbo I Set 5.8-Gallon Wet/Dry Extractor (corded)

The Turbo I Set is a corded 5.8-gallon wet/dry extractor with a 1100W turbine. The listing states 151 CFM and 98 of water lift, a 19 ft power cord, a 13 ft vacuum hose and an autostart outlet with a power-on delay. The listing describes that delay as a way to prevent current spikes when a tool starts.

Power: corded electric (listing)
Capacity: 5.8 gallon (title)
Airflow: 151 CFM and 98 of water lift (listing; the extracted text prints no unit for 98)
Cord and hose: 19 ft cord and 13 ft vacuum hose (listing)
Filter: HEPA filter; the title says the set includes a filter and accessories
Outlet: autostart with power-on delay (listing)
Swivel wheels: 360 degree rotation (listing)
Weight: not stated

Skip it if you need a cordless unit or the cord is too short for your outlet. The limit is the unlabeled water-lift figure, which the listing prints without a unit in the extracted text. The HEPA Pro Set below lists the same airflow and cord figures.

Fein Turbo I HEPA Pro Set 5.8-Gallon Wet/Dry Extractor (corded)

The HEPA Pro Set uses the same 5.8-gallon body, 151 CFM figure and 19 ft cord as the Turbo I Set. Its listing adds a HEPA filter and filter bag, and says the included HEPA filter and bag capture fine dust and particles. The listing says the unit is approved for dust class L.

Power: corded electric (listing)
Capacity: 5.8 gallon (title)
Airflow: 151 CFM and 98 of water lift (listing)
Filter: HEPA filter and filter bag; approved for dust class L (listing)
Cord and hose: 19 ft cord; 13 ft anti-static hose (listing)
Outlet: autostart with soft-start (listing)
Weight: not stated

Skip it if you do not need the filter bag, since the airflow and cord figures match the Turbo I Set. The limit is that the listing does not say whether its HEPA filter is a different model from the one in the Turbo I Set.

Bosch GDE18V-26DB15 Mobile Dust Extractor Kit

This is a mobile dust extractor for hammer drilling, not a floor vacuum. The listing says it is designed to fit the Bosch 18V cordless bulldog D-handle and several corded Bosch bulldog and rotary hammer models. The kit includes one CORE18V 4 Ah battery, and the listing says the dust container has capacity for up to 20 holes drilled with a 1/2 inch bit to a depth of 2 inches in concrete.

Power: battery powered, 18 volts (listing)
Battery: one CORE18V 4 Ah battery in the kit (title)
Filter: HEPA (listing)
Dust eyes: 5/8 inch and 1 inch sizes; 4 inch extension (listing)
Dust container: up to 20 holes, 1/2 inch bit, 2 inches deep into concrete (listing)
Airflow and weight: not stated

Skip it if you need a vacuum for floors, carpet or wet spills, because the listing describes a drilling accessory. Its limit is that capacity is stated in holes rather than in gallons, and the listing gives no airflow figure. View on Amazon

How we chose

We searched Amazon for “dust extractor” on 2026-10-22 and opened nine listings that sell the product under the dust extractor name. The criteria were the things each listing states plainly: the power source (corded, a battery platform, or a kit with a battery), the airflow and filter figures, and the cord or hose length. Shop vacuums without the extractor name, nail-tech dust collectors, handheld dust buster vacuums and rotary hammer attachments appeared in the search results and were left out. All nine listings were read in full on that date, and the figures are the listing’s own.

What we could not verify

How much fine dust each unit captures on a real job. The figures are what each listing says, and they use different measures and conditions, so they do not compare cleanly.
Whether a unit fits a particular saw, sander, router or hammer drill. Some listings name compatible tools, but the adapter fit for your tool is not confirmed here.
Battery runtime at any load other than the one each listing states.
Whether the HEPA filters are the same across listings. Several listings name HEPA, but the extracted text names one filter part number, DWV9330, and only for the DWV010.

What the sources do not say

Whether a battery comes in the box for the DCV585B or the DWH161B. The DCV585B listing does not say, and the DWH161B is sold as tool only.
Weight or hose length for several units. The Makita VC4210L and the XCV04Z list neither in the extracted text.
The unit for the Fein water-lift figure of 98, which the extracted text prints without one.
Which DWV010 airflow figure is correct. The listing gives 150 CFM in a bullet and 155 CFM in the description.
Warranty length. The DWV010 text says the manufacturer warranty can be requested from customer service, but no length is given.

Buying checklist

Note the battery platform you already own, and buy only a unit that names it.
Read the battery line in the box contents. Tool only means no battery and no charger.
Compare airflow figures only between units that state the same power source.
Confirm the hose or adapter for your tool before you buy the extractor.
If the job follows an EPA lead-safe rule, check the filter the listing requires.

FAQ

Is a dust extractor the same as a shop vacuum?

The listings use the term for units that connect to power tools, usually through a tool-activated or autostart outlet. The DEWALT DWV010, the Makita VC4210L and both Fein Turbo I sets list such an outlet. The listings do not say a standard shop vacuum works the same way, so check the outlet feature before you buy.

Do I need a battery to run one?

Only the battery units need one. The Bosch GDE18V-26DB15 kit includes one CORE18V 4 Ah battery. The DWH161B, the XCV11Z and the XCV04Z are sold as tool only, and the Makita listings say the battery is not included. The DCV585B listing does not say whether a battery comes with it.

What does tool only mean for these units?

It means the box holds the extractor and no battery or charger. Buy the battery for your platform separately, and match its voltage to the tool. Do not assume a battery from another brand fits, because the listings name only their own platforms.

Do these units all have HEPA filters?

All nine listings name a HEPA filter in some form. The Makita XCV11Z says its HEPA filter captures 99.97 percent of particulates 3 microns and larger, and the Makita VC4210L gives the same 99.97 percent figure at the same size. The DEWALT DWV010 says it meets the EPA Lead Related Renovations rule only when DWV9330 filters are used.

Can I use one with my sander or saw?

Some listings name the tools they fit. The DWH161B listing names sanders, routers and jig saws among its uses, and the DCV585B lists tuckpointing and surfacing applications. None of the listings confirms fit for your specific tool, so check the adapter list for your model before you buy.

Why do the airflow figures differ between listings?

Each listing gives its own figure, and the figures do not always share a condition. The DWV010 page gives 150 CFM in one place and 155 CFM in another. The Makita XCV04Z lists a corded figure of 127 CFM and a battery figure of 74 CFM. Compare the figure that matches the power source you will use.

Bottom line

Match the power source first: choose the extractor whose battery platform you already own, or a corded unit if you have none, and use the stated airflow only to compare units that run on the same power.

Sources

DEWALT DWV010 HEPA Dust Extractor with Automatic Filter Cleaning, 8-Gallon (opened 2026-10-22) https://www.amazon.com/dp/B00OA02TZ0
DEWALT 20V MAX Dust Extractor, Brushless, Universal, Tool Only (DWH161B) (opened 2026-10-22) https://www.amazon.com/dp/B07WQB34DX
DEWALT FLEXVOLT 60V MAX Dust Extractor (DCV585B) (opened 2026-10-22) https://www.amazon.com/dp/B07N2KBM8W
Makita XCV11Z 18V LXT Lithium-Ion Brushless Cordless 2 Gallon HEPA Filter Portable Wet/Dry Dust Extractor/Vacuum, Tool Only (opened 2026-10-22) https://www.amazon.com/dp/B07M8JTDNS
Makita VC4210L 11 Gallon Wet/Dry HEPA Filter Dust Extractor/Vacuum (opened 2026-10-22) https://www.amazon.com/dp/B07ZMN75V2
Makita XCV04Z 36V (18V X2) LXT/Corded 2.1 Gallon HEPA Filter Dry Dust Extractor/Vacuum, Tool Only (opened 2026-10-22) https://www.amazon.com/dp/B01FXQ6CLQ
Fein Turbo I Set Wet/Dry Dust Extractor 5.8-Gallon Capacity (opened 2026-10-22) https://www.amazon.com/dp/B00K69ILFQ
Fein Turbo I HEPA Pro Set Wet/Dry Dust Extractor 5.8-Gallon Capacity (opened 2026-10-22) https://www.amazon.com/dp/B0CKDT5WPM
BOSCH GDE18V-26DB15 SDS-plus Bulldog Mobile Dust Extractor Kit with (1) CORE18V 4 Ah Advanced Power Battery (opened 2026-10-22) https://www.amazon.com/dp/B07PS7NDRT